1-10 fan on relay. 2012-03-13 99 Mack ch600 electronic malfunction light came on and truck is spitting and sputtering.
5-8 ASET CEGR EGR Temperature.
Mack truck electronic malfunction light. Replace right away it will let you down completely. Using the cruise control set switch it will flash 3 then 5 or 35. I changed the radiator due to the old one leaking and after I replaced it I filled the antifreeze to the level.
1-3 fuel temperature sensor. Humped it up to the dog house for a new one98 freakin dollars. Reply profile send pm notify.
5-7 Engine Oil Level. 2008-01-19 You can check your codes with the cruise control switchs but you must have a stored code ie CEL stays on You do itby having key on cruise power switch off and hold RESUMEACCEL switch on until CEL light goes out. If the temperature remains below or exceeds the normal temperature range the cooling sys- tem should be checked for problems by an authorized Mack Vehicle dealer.
1-8 ASET CEGR estimated fan speed. 6-2 ASET CEGR Turbocharger Speed. But usually it will set the malfunction light cause the trucks ecu thinks the park brake is set.
I am thinking it is. The light doesnt come on while driving. 2008-12-23 Are you getting any electronic malfunction light on the dash coming on.
Truck Diagnostic System is our easy-to-use PC-based diagnostics software solution for the diagnosis and maintenance of US07 US10 or US13 model Mack truck engines. 8 years ago. Since its initial vehicle test run in December 1988 V-MAC has logged more than two million miles of on-highway evaluation.
Comment profile send pm notify. Used in conjunction with an RP1210A compliant vehicle interface adapter Truck Diagnostic System software reads vehicle controllers on the truck and displays detailed fault codes and component data in an easy. Operators Manuals PDF Anthem CH CHN DM DMM Granite GU LR Pinnacle CHU CXU TerraPro MRU Titan R series FP Diesel Parts V-MAC 4 MP7 MP8 MP10 Truck Engine Service Manual are above the page.
2018-06-11 Some MACK Truck Service Manuals. Safety How YouTube works Test new features Press Copyright Contact us Creators. I am getting a electronic malfunction and shut down alarmthe engine kills.
I also checked all sensors and harnesses and they were all fine. Ask Your Own Medium and Heavy Trucks Question. 1-2 atmospheric pressure sensors.
Posted by R. 2016-02-16 The electronic malfunction light only comes on when I have the PTO engaged doesnt flash just stays on steady. 1-1 oil pressure sensor.
MACK Trucks was founded June 11 1900 New York NY USA. I do believe that the DRLs used the park brake air pressure switch for activation signal. 2020-01-06 5-5 Electronic Malfunction Lamp.
2013-03-24 Found the culprit to be the oil pressure sensor otop of the filters. When coolant temperature is excessive the red STOP tell-tale illuminates and the buzzer will sound. 1-6 no starter start.
What do think might be the problem. 6-9 Other ECU. Turns over longer than normal.
6-5 All Communication Lost – Engine Shutdown. Ask Your Own Medium and Heavy Trucks Question. Answered in 9 hours by.
Is the engine starting a little rough. Mack 2006 electronic malfunction light turned on and blinks When checked in manual it looks like coolant sensor needs to changeNow changed with new sensor but still same issue. Light come on while enroute there is a power loss that you can feel more when loaded.
The normal operating temperature for Mack engines is 80 to 105. Both lamps illuminate while an alarm sounds for two seconds whenever the vehicle is started. The light will start flashing the codes.
2014-07-15 Dude the lightning bolt means electrical fault in order to see the code push the odometer reset and trip button same time and release it. Lift pump bottom right side of engine. I have a 2000 mack ch613 with a 460 engine electric malfunction light has been coming on then it shuts down if you hold cruise down while malfunction light is on the blinks seven times the five times is this a code for something.
You get an electronic malfunction light but it wont shut off cause of this anymore. 5-9 ASET CEGR EGR Mass Flow. Medium and Heavy Trucks.
2018-10-23 Mack truck code faults list. In 1990 Mack Trucks completely passed under the. 6-6 Fuel Control Module.
5-6 Spare Relay 3. The blink code in the V-MACK book says it is shutting down on a low oil pressure but the guage shows 60 psi. Question about Cars.
Answered in 8 hours by. 1990-08-13 An amber light indicates an electrical malfunction while a red lamp signals an engine parameter out of range. 1-4 atmospheric air sensors.
Diesel-tech Mechanic replied. 2018-11-17 I got a 1998 Mack CH613 that shows the electronic malfunction light. Unplug it jumped the to side by sides and off we go.
2011-03-24 M R Mack problem. That is the component that I mostly see causing that complaint. 2016-05-09 I have a 1994 CH 613 wE7 350 that periodically has electronic malfunction.
Itll be a two digit with a slight pause between seperate codes.